Wood Floor Installation in Myrtle Beach, SC
New floors are one of the most impactful things you can do for a home. They change how a room feels. They affect resale value. They're something you and everyone who walks through your front door will notice every single day.
But getting it right takes more than picking a wood species off a sample board and scheduling a crew.
It takes someone who understands the product, the subfloor it's going on top of, and the environment that floor is going to live in. In Myrtle Beach and along the Grand Strand, that last part matters more than most people realize. Coastal humidity doesn't forgive shortcuts. Wood that wasn't acclimated properly, installed over a subfloor that wasn't checked, or chosen without accounting for moisture levels — it's going to move. It's going to cup. It's going to cause problems that show up six months after the installer is long gone.
That's not how we work.
Every installation we do starts with moisture testing and a thorough subfloor assessment. We tell you exactly what product makes sense for your home, your subfloor type, your moisture situation, and what you're actually going for aesthetically. And we build proper acclimation time into every single job — not as an afterthought, but as a standard part of the process.
We install solid hardwood, engineered wood, wide plank, reclaimed, herringbone, chevron, pre-finished, unfinished, glue-down, nail-down, bamboo, and exotic species for homeowners and commercial clients from Myrtle Beach to Conway, Pawleys Island, North Myrtle Beach, and everywhere in between.
Floors We Professionally Install
Solid Hardwood Flooring Installation
Solid hardwood is the original. One solid piece of wood — white oak, red oak, hickory, maple — milled from top to bottom. It's been the standard for generations because when it's installed correctly and maintained properly, it outlasts just about everything else. You can refinish it multiple times over its life. Done right, solid hardwood in a home is a permanent feature.
The tradeoff is moisture sensitivity. Solid hardwood expands and contracts with humidity, and in Myrtle Beach, that's a real consideration. It doesn't mean solid hardwood is off the table — it means the installation has to be done correctly.
We run moisture tests before anything goes down. We acclimate the wood to your home's specific environment — not just a day or two, but the proper amount of time for the product and the conditions. And we make sure the subfloor underneath is level, dry, and ready. Skip any one of those steps and you'll have problems. We don't skip them.
Solid hardwood works well in living rooms, bedrooms, dining rooms, and above-grade spaces with controlled humidity. We'll tell you honestly whether it's the right fit for your specific home before any material gets ordered.
Engineered Wood Floor Installation
Engineered wood is real hardwood on top — a genuine hardwood veneer bonded to multiple layers of plywood underneath. Those layers are what make it different. They run in alternating directions, which makes the whole product more dimensionally stable than solid hardwood when humidity changes.
For homes along the Grand Strand, engineered wood is often the smarter choice. If you're on a slab foundation — which a large percentage of Myrtle Beach homes are — engineered wood handles the moisture conditions at grade level far better than solid hardwood. If your home is closer to the water, if your HVAC system doesn't always keep humidity tightly controlled, or if you're installing in a space that sees more moisture exposure, engineered is frequently the right answer.
It also opens up installation options that solid hardwood doesn't. Engineered wood can be glued down over concrete, floated, or nailed down over wood subfloors — which gives us more flexibility depending on what we find during the subfloor assessment.
There's a lot of engineered wood on the market at a wide range of price points. The veneer thickness matters. The core construction matters. We work with quality products that are actually worth what you're paying for them, and we'll walk you through the differences so you understand what you're getting.
Wide Plank Wood Floor Installation
Wide plank flooring — generally anything 5 inches or wider — has a visual weight that narrow strip floors just can't replicate. The boards show off more grain. The floor feels more open. Rooms feel bigger. And in a coastal home, that broader, more relaxed look fits the space.
Wider boards do require more attention during installation. They're more sensitive to subfloor imperfections. They move a bit more with seasonal humidity changes. The fastening pattern matters. None of that is a problem when you know what you're doing — but it's the kind of detail that separates a floor that looks beautiful for years from one that starts showing gaps or movement within a season.
We do wide plank installations in both solid and engineered formats. We help you pick the right species and format for the scale of your room, and we make sure the subfloor is properly prepped before a single board goes down.
Wide plank white oak has been particularly popular in Myrtle Beach and the surrounding area over the last several years — both in new builds and in renovation projects where homeowners are upgrading from builder-grade strip flooring. It suits the coastal aesthetic well and holds up to foot traffic reliably when finished correctly.
Reclaimed Wood Flooring Installation
There's a version of a wood floor you can get from a showroom. And then there's a version you can only get from an old building that no longer exists.
Reclaimed wood — salvaged from barns, factories, warehouses, mills, and old structures — has a character that no new material can replicate. The nail holes are real. The saw marks are real. The weathering happened over a hundred years, not in a finishing plant. Every board has a history, and when that history gets laid across your floor, the result is genuinely one of a kind.
It's also a product that requires specific handling. Reclaimed material has to be properly cleaned, inspected, and prepared before installation. Moisture content has to be checked carefully. And installation requires more patience because every board is different.
We've sourced and installed reclaimed wood for homeowners along the Grand Strand who wanted something that couldn't be found in a catalog. If this is the direction you're thinking, it's worth a conversation to talk through sourcing options, realistic expectations, and what the installation process looks like.
Herringbone & Chevron Pattern Installation
Herringbone and chevron pattern floors are having a moment in Myrtle Beach — in newer custom builds, in Market Common townhomes, and in renovation projects where homeowners want a floor that becomes a design statement instead of a background detail.
Both patterns are more complex to install than standard straight-lay flooring. The angles have to be precise. The layout has to be planned carefully based on the room's dimensions and entry points. If the pattern doesn't line up correctly, it's immediately visible and very difficult to correct after the fact.
Done right, herringbone is one of the most striking floors you can install. Done sloppily, it looks worse than a standard straight lay. The difference is entirely in the execution.
We do both herringbone and chevron in solid hardwood, engineered wood, and parquet formats. We plan the layout in advance, account for the room's geometry, and take the time to get the pattern exactly right before we start putting boards down.
Unfinished Wood Floor Installation
Unfinished (left), Pre-Finished (right)
Unfinished hardwood gets installed first and then sanded and finished on-site after the boards are down. The finish is applied directly to the fully installed floor, which means it bonds to the actual surface and fills any small gaps between boards.
The result is a floor that looks and feels truly seamless. There are no factory edges, no pre-applied finish that sits slightly above the board surface — just a continuous, uniform finish across the entire floor.
Unfinished installation also gives you complete control over stain color and finish sheen on-site, after you've seen how the wood looks in your actual lighting and space. A lot of homeowners prefer this because what looks right under showroom lighting doesn't always look right in your home.
The tradeoff is time. The floor needs to be sanded, stained if desired, and finished with multiple coats — with drying time between coats. The space will be out of use for a few days during the process. If your timeline allows for it, unfinished installation typically produces a higher-quality final result.
Pre-finished Hardwood Installation
Pre-finished hardwood comes from the factory already sanded and coated with a durable finish. Once it's installed, you can walk on it. No waiting for finish coats to cure, no dust from on-site sanding, no extended downtime.
For homeowners who need to minimize disruption — families with young kids, people who can't vacate the space for several days, vacation rental owners who have a tight window between bookings — pre-finished is often the practical choice.
The finish is typically aluminum oxide, which is extremely hard and resistant to wear. It's not as seamless as an on-site finish job, but it's highly durable and available in a wide range of species, stain colors, and sheen levels.
We'll walk you through both options and give you an honest read on which makes more sense for your situation. There's no wrong answer — it comes down to your priorities.
Glue-Down Wood Flooring
Glue-down installation means the flooring is adhered directly to the subfloor using a flexible adhesive. It's the standard method for wood flooring over concrete slabs, which is a very common scenario in Myrtle Beach given how many homes here are built on slab foundations.
Done correctly, glue-down installation produces a very stable floor with no movement underfoot. The adhesive also acts as a moisture barrier between the slab and the wood, which matters in a coastal climate.
The adhesive has to be the right product for the flooring and subfloor combination. The slab has to be properly prepared — clean, level, and within acceptable moisture limits before anything goes down. We test before we install. If the slab isn't ready, we tell you what needs to happen before we proceed. Installing over a slab that hasn't been properly checked is one of the most common causes of flooring failures we see in this area.
Nail-Down Hardwood Installation
Nail-down installation is the traditional method for solid hardwood over wood subfloors. Cleats or staples are driven through the tongue of each board at an angle, fastening the flooring securely to the subfloor below.
It's a proven method that's been used for over a century because it works. A properly nailed floor is solid underfoot, doesn't shift or flex, and holds up to decades of use without fastener issues.
The subfloor condition matters. It needs to be structurally sound, flat, and within acceptable moisture limits. Squeaks in a nail-down floor are almost always a subfloor issue, not an issue with the flooring itself — which is why the prep work before installation is so important.
We assess the subfloor thoroughly before any nail-down job. If there are soft spots, high/low areas, or moisture concerns, we address them before the flooring goes down. That's the step that most problems trace back to when they're skipped.
Bamboo & Exotic Wood Installation
Brazilian Cherry
Tigerwood
Acacia
Bamboo
If you want something outside the standard oak, hickory, and maple options — this is where things get interesting.
Brazilian cherry brings a deep, rich reddish-brown tone that darkens further with light exposure over time. It's one of the hardest flooring species available and holds up extremely well in high-traffic spaces.
Tigerwood is striking — warm orange-brown tones with dark, irregular streaking that gives it a genuinely unique visual character. No two floors look exactly alike.
Acacia offers dramatic variation in color and grain, ranging from lighter honey tones to deep browns, often within the same board. It's dense, durable, and visually bold.
Bamboo is technically a grass, but it's harder than most domestic hardwood species and performs well in high-humidity environments — which makes it worth consideration in coastal Myrtle Beach homes. It installs similarly to hardwood and comes in a variety of colors and formats.
These materials require specific handling, appropriate adhesives, and finishes that are matched to the species. We know how to work with them properly and source quality products that perform over time.
Commercial Wood Flooring Services
Wood floors in commercial spaces face a different set of demands than residential floors. Higher foot traffic. Heavier furniture. Tighter installation windows. Turnover schedules that don't flex.
We work with restaurants, retail stores, offices, boutique hotels, event spaces, and historic commercial properties throughout Myrtle Beach and the Grand Strand. We plan commercial jobs around your operational schedule — whether that means working evenings, weekends, or phasing the installation to keep part of your space operational.
Commercial flooring also requires products and finishes rated for the traffic load the space will actually see. Residential-grade finishes wear down quickly in commercial environments. We spec the right materials from the start so you're not calling us back in two years because the finish failed.
If you're opening a new space, renovating an existing one, or managing a property that needs flooring work without significant downtime, give us a call and we'll talk through what the project actually requires.
What to Expect When You Work With Us
Most flooring jobs follow the same basic sequence:
1. Initial assessment — We come out, look at the space, test moisture levels, evaluate the subfloor, and talk through your goals and budget.
2. Product recommendation — Based on what we find, we tell you what products are realistic for your situation and what the tradeoffs are. No pressure, no upselling — just a straight recommendation.
3. Acclimation — The flooring material gets delivered and acclimated to your home's temperature and humidity before installation begins. This step is non-negotiable for us.
4. Subfloor prep — Any subfloor issues get addressed before a single piece of flooring goes down.
5. Installation — The floor goes down using the method appropriate for your subfloor type and product.
6. Finishing — For unfinished installations, sanding and finishing happens on-site after installation is complete. For pre-finished, the floor is ready to walk on at completion.
7. Final walkthrough — We go through the finished floor with you before we leave.
Wood Floor Installation FAQs
How much does wood floor installation cost in Myrtle Beach, SC?
Wood floor installation in the Myrtle Beach area typically ranges from $6 to $14 per square foot installed, depending on the species, format (solid vs. engineered), installation method, subfloor condition, and any prep work required. Exotic species, wide plank, reclaimed wood, and pattern installations like herringbone run higher. The best way to get an accurate number is a site visit — there are too many variables to give a reliable quote without seeing the space.
How long does wood floor installation take?
A standard installation for an average-sized home usually takes two to four days for the installation itself. Unfinished installations add time for sanding and finishing, typically another two to three days. Larger homes, complex patterns like herringbone, or significant subfloor prep work will extend the timeline. We give you a realistic schedule upfront so there are no surprises.
Do I need engineered or solid hardwood for my Myrtle Beach home?
It depends on your subfloor type and your home's moisture conditions. If you're on a concrete slab — which is common in Myrtle Beach — engineered wood is usually the right call. If you have a wood subfloor with controlled humidity and proper acclimation, solid hardwood is absolutely viable. We test moisture levels and assess the subfloor before making any recommendation. We'll give you an honest answer based on your specific situation.
How long does the wood need to acclimate before installation?
Typically between three and seven days, depending on the product and your home's humidity levels. Some situations call for longer. We don't rush this step — flooring installed before it's properly acclimated will move after installation, and that's not something that can be easily fixed after the fact.
What subfloor preparation is required before installing hardwood floors?
The subfloor needs to be structurally sound, flat within manufacturer tolerances (typically 3/16 inch over 10 feet), dry, and clean. Soft spots, high/low areas, and moisture issues all need to be addressed before flooring goes down. We assess all of this during the initial visit and include any necessary prep in the project scope.
Can wood floors be installed over concrete?
Yes — engineered wood and certain solid hardwood species can be installed over concrete using a glue-down method with appropriate adhesive. The concrete has to be within acceptable moisture limits and properly prepared. We test before we install, and if the slab isn't ready, we tell you what needs to happen first.
How long before I can walk on newly installed hardwood floors?
Pre-finished hardwood can be walked on immediately after installation. Unfinished installations require waiting for finish coats to fully cure — typically 24 hours for light foot traffic and 48 to 72 hours before moving furniture back in, depending on the finish type. We give you specific guidance based on your project.
Do you handle subfloor repairs as part of the installation project?
Yes. If we find subfloor issues during the assessment, we handle the repair as part of the overall project. We'd rather take the time to do it right than install over a subfloor that's going to cause problems later.
Can you install wood floors in a commercial space without shutting the business down?
In many cases, yes. We're experienced working around operational schedules — phasing installations, working off-hours, or planning around your specific business needs. It depends on the size of the space and the scope of the project. We'll talk through what's realistic during the initial consultation.
What wood species do you recommend for coastal homes in Myrtle Beach?
For solid hardwood, white oak and hickory are excellent choices — both are dense, stable, and handle normal humidity variation well when properly installed. For engineered, the species selection opens up more since the core construction does much of the stability work. Bamboo is also worth considering in high-humidity situations. We'll give you specific recommendations once we've assessed your home's conditions.